Monitor. Balance. Protect.

Track and Synchronization Control for Bridge Cranes

Our track and alignment control system continuously monitors your crane’s undercarriage and automatically corrects any deviations. The wheels remain centered on the rail, protecting both the flanges and the rails.

Runout wears down flanges and rails

Virtually no crane travels exactly straight on its own. Tolerances in the wheels and crane runway, differences in wheel diameters, or drives that do not run evenly cause the crane girder to travel at an angle.

Then the flange presses against the rail from the side. With every trip, the wheel and rail rub against each other, and the bridge structure becomes stressed.

Leere Industriehalle mit Brückenkran über einer langen Kranbahn

It doesn’t stop at the worn-down flange

Replacement of Wheels and Rails
Worn wheels must be reconditioned or replaced, and damaged rails must be replaced.
Loads on the Support Structure and Crane Runway
Lateral forces create tension in the crane structure and place stress on the rail fastenings and crane runway girders.
Downtime for Maintenance
Any repair to the undercarriage or crane runway takes the crane out of service.

Misalignment costs
on every trip

Wear and tear increases with every crane movement, often going unnoticed until the next inspection.

The result is worn-out flanges and rails, and downtime for maintenance.

Limitations of Common Solutions

Mechanical guidance, lubrication, and regular readjustment are used to prevent misalignment. These measures help, but they primarily address the consequences.

Guidance via the flange

The flange absorbs lateral forces and wears down along with the rail.

Side Guide Rollers

They reduce wear, but they only absorb the lateral forces instead of correcting the misalignment.

Lubrication

It reduces friction between the flange and the rail. However, it does not eliminate the misalignment itself.

Readjust

Aligning the crane track and wheels requires the crane to be at a standstill and only corrects the condition as it exists at the time of measurement.

Your crane with our track and synchronization control system

Centered wheels
The system keeps the wheels continuously centered on the track.
Synchronous operation on both sides
Both sides of the crane bridge move synchronously. Deviations between the carriages are automatically corrected.
Less Stress
This control system minimizes stress in the crane structure.
Inductive or Laser-Based
Inductive or laser sensors are used as the measurement system. The control parameters can be adjusted for different crane systems.
Kopfträger eines Brückenkrans mit Fahrantrieb auf der Kranbahn, von unten gesehen

Actively controlled instead of
mechanically guided

Sensors continuously monitor the track position of both landing gear.
Our controller compensates for deviations and keeps the wheels centered on the track.

Step 1

Sensors

Inductive sensors or laser sensors measure the position of the wheels relative to the rail on both sides.

Step 2

Cranium Track Control

The controller on the industrial PC calculates the deviation and the necessary correction for each landing gear.

Step 3

Crane PLC

The PLC adjusts the drive motors until the impellers are running centered again.

Interested in track and synchronous control for your crane?

Find out how we can help.

Our Track and Synchronization Control in Day-to-Day Operations

Longer service life

Less material wear extends the service life of wheels and rails.

Less Maintenance

When there is less wear and tear, parts need to be repaired or replaced less often.

PLd-compatible

Multiple sensor channels make the control system PLd-capable (Performance Level d).

Monitored on every trip

Wheel alignment is monitored continuously, not just during the next inspection.

Guided Commissioning

Setup is performed step-by-step using the Cranium web application.

Individually or in combination

The Track Control operates either on its own or in conjunction with the Sway Damping system and other Cranium modules.

Request information about our track and alignment control system for your crane

Protect your wheels, rails, and crane structure with our track and alignment control system.

Martin Kirst
Geschäftsführer

Richard Herrmann
Prokurist

Uwe Ochs
Vertrieb

Suitable modules

Scroll to Top